Table of Contents
- What should the quotation state instead of a size promise?
- Why are CSS, OSS and product top size different?
- Which discharge stream must meet the requirement?
- When is a jaw-only offer suitable, and when is it incomplete?
- Can tightening the gap replace missing process scope?
- What should be agreed before accepting the purchase?
- Frequently asked questions
- Does a 50 mm CSS mean every stone will be smaller than 50 mm?
- Can I calculate CSS from any measurement taken at rest?
- Should the product sample include grizzly bypass?
- Does a jaw crusher always need a downstream screen?
- Can a smaller setting keep the same quoted production rate?
- What evidence should support a top-size commitment?
- Choose the offer around the accepted stream
- Sources and technical references
Can a Jaw Crusher Setting Guarantee Product Top Size?
A jaw crusher setting alone cannot guarantee that every discharged stone will pass a sieve of the same size. The closed-side setting describes the crushing gap, while product acceptance concerns a measured size distribution from a defined material stream. Before buying a mobile primary jaw crusher, require the proposed setting, permitted operating range, feed basis and product grading to be stated separately. If a strict top-size limit applies, compare the necessary separation and further-crushing scope as well. Accept the proposal against an agreed sampling point and sieve criterion, including any bypass material that rejoins the discharge.

By MVSI Company. Published 2026-11-21.
What should the quotation state instead of a size promise?
Require a mechanical setting and a separate product acceptance definition. A number described only as output size leaves the purchase obligation ambiguous.
| Decision fact | Record to request | Buying implication |
|---|---|---|
| Mechanical gap | CSS or OSS, exact model, jaw profile and permitted range | An opening is not a complete grading specification |
| Product requirement | Sieve sizes, percent passing and allowed oversize under the project specification | A coarse primary feed and a specified aggregate are different duties |
| Material stream | Jaw-only discharge, combined bypass/discharge or screened final product | Evidence must describe the stream actually handed over |
| Feed and rate basis | Representative feed grading, material condition and required capacity in t/h | Compare the same feed and accepted output basis |
| Acceptance point | Agreed sampling location, method, operating condition and responsibility | A setting indicator or photograph cannot replace grading evidence |
The MVSI mobile primary jaw crusher family provides a relevant starting point for primary quarry and mining duties. Request the exact offered model and setting documentation. The public family description does not establish a project-specific top-size guarantee; no numerical product rating is assumed here.
Why are CSS, OSS and product top size different?
Closed-side setting (CSS) is the minimum discharge gap during the jaw cycle; open-side setting (OSS) describes the larger opening. A sieve result measures the material passing a specified aperture, rather than the machine opening.
Metso’s C-series application guide explains its at-rest OSS measurement and derives CSS using the model-specific stroke. It also varies the measurement reference with tooth profile and directs users to the manual for the minimum permitted CSS. Ask for the corresponding definitions for the machine offered; do not borrow another model’s stroke or measurement reference.
This is a documentation check, not an instruction to reach into a jaw or measure moving equipment. The exact manufacturer’s isolation and inspection procedure governs any physical check. A supplier’s indicator reading should be tied to the stated measurement convention before it is used in an acceptance record.
An OEM chart makes the distinction concrete. The Terex 2025 pocket reference, printed page 38, shows 79% passing a 2-inch sieve at a 2-inch CSS, with 100% passing at 3 inches in that chart. Those apertures are 50.8 mm and 76.2 mm. This is an attributed reference example, not an MVSI prediction or a universal conversion. It demonstrates why a setting of 2 inches cannot simply be read as every particle being below 2 inches.
Which discharge stream must meet the requirement?
The specified sampling point must follow the material the buyer will actually receive. A jaw-only sample cannot establish the grading of a combined stream when other material joins it.
Trace the proposed arrangement from feeder to delivery point. Does grizzly bypass go to a reject pile, join the jaw discharge, or enter another process? Does the acceptance sample come before or after that junction? The question is not whether bypass is inherently good or bad: its destination and grading must be included in the agreed handover basis.
| Sample or record | What it addresses | What remains unresolved |
|---|---|---|
| Jaw discharge before a junction | Primary-crusher output under the recorded feed and setting | The effect of material joining downstream |
| Combined discharge after bypass joins | The stream delivered by that combined route | Any later separation or product blending |
| Final screened product | The product from the specified screen outlet | Crusher-only performance or another outlet’s quality |
| Setting and jaw-condition record | Mechanical operating condition associated with the sample | Percent passing without actual grading evidence |
For the broader interface decision, see when a hard-rock quarry needs a jaw and cone circuit. Here the narrower requirement is to name the accepted stream before deciding whether the jaw offer alone covers the job.

When is a jaw-only offer suitable, and when is it incomplete?
A jaw-only offer can remain a candidate when its supported discharge grading meets a defined primary-stage handover requirement. It is incomplete when the buyer requires a final fraction but the offer documents only a gap setting.
Illustrative quotation comparison, not a customer project: a quarry requests material for the next process stage. Offer A states a jaw setting and machine feed rate; Offer B also identifies the intended handover grading, bypass route and acceptance point. Do not assume B performs better. First ask A to price and document the same obligation, then compare both offers. If the requirement changes to a strictly controlled saleable fraction, request the required screening and, where necessary, further-crushing scope from both suppliers.
- Keep a primary-jaw comparison when the downstream receiver has an agreed feed envelope and the proposal supports that handover.
- Retain screening in the scope comparison when oversize must be separated from an accepted product. Name the oversize destination and any return or further-crushing route.
- Do not select an extra crusher merely because the setting differs from the sieve limit. Ask what the actual grading evidence and process assessment require.
- Compare equipment, conveyors, stockpile routes and acceptance work on the same boundary. No numerical price or guaranteed yield follows from this example.
Can tightening the gap replace missing process scope?
Treat a tighter setting as an operating choice inside the exact machine’s permitted range, with rate and wear implications. It does not resolve an undefined product criterion or sampling point.
EvoQuip’s wear-parts guide warns that a tighter CSS increases jaw-plate wear and that operation must respect the manual’s minimum setting. Metso likewise identifies CSS as relevant to capacity, power, grading and wear. Request a supported duty assessment at the proposed setting instead of assuming that a smaller number preserves the quoted rate.
Record jaw condition alongside the operating setting when comparing samples. If the underlying issue is a worn or unsuitable plate, use the separate jaw-plate turning and replacement guide. Buying replacement plates, reducing the gap and adding a screen are different decisions; the grading record should show which question actually needs resolving.
What should be agreed before accepting the purchase?
Agree the product definition and evidence plan before award, including who supplies missing material data. A general statement that the crusher will make the requested size is insufficient.
- Attach the feed description, representative grading, moisture/clay condition and target rate to the offer; identify assumptions requiring confirmation.
- State each product sieve and its percent-passing or oversize limit using the applicable project specification. Do not replace the whole grading envelope with one top-size number.
- Identify the physical sample point on the arrangement drawing, including bypass, screen return and blending junctions.
- Agree the sampling and sieve method, stable operating conditions, duration, responsibility and response if the result falls outside the requirement. This article does not prescribe a universal test standard.
- Record the exact machine, jaw profile/condition and setting convention used for the evidence. Separate a preliminary calculation from a demonstrated result or contractual guarantee.
Use the hard-rock jaw quotation comparison guide for the wider commercial and installation boundaries. The specific addition here is to prevent the mechanical gap from becoming an undefined product guarantee.
Frequently asked questions
These answers concern product-size acceptance for a primary jaw purchase; the exact machine documentation and project specification remain necessary.
Does a 50 mm CSS mean every stone will be smaller than 50 mm?
No. CSS describes a mechanical gap, not a promise that all discharge passes the same sieve aperture. Request a supported product grading and an agreed oversize criterion for the specified stream.
Can I calculate CSS from any measurement taken at rest?
Only with the exact machine’s approved measurement convention and required stroke information. Tooth references and model details matter. Follow the manufacturer’s isolation and inspection procedure for any physical measurement.
Should the product sample include grizzly bypass?
Include it when that bypass rejoins the stream covered by the acceptance requirement. A jaw-only sample describes a different boundary. Mark the junction and sample point on the process drawing.
Does a jaw crusher always need a downstream screen?
No. It depends on the agreed handover grading and evidence for the proposed duty. A strict separated product requirement may need screening; a primary feed for another process can have a different acceptance basis.
Can a smaller setting keep the same quoted production rate?
Do not assume so. Ask for the rate basis at the proposed setting and material condition, within the permitted operating range. Compare wear and power implications as part of that assessment.
What evidence should support a top-size commitment?
Require the product criterion, feed and operating basis, exact sampled stream, agreed sampling and sieve method, and a clear distinction between estimates, demonstrated results and contractual acceptance obligations.
Choose the offer around the accepted stream
Compare a jaw-only purchase when the supported primary discharge meets the next stage’s defined requirement. Include the necessary separation or further-crushing scope when the required product cannot be supported by that offer. Resolve the grading and sample point before treating any setting as a guarantee.
For a matched proposal, contact MVSI through its listed WhatsApp or email route. Send raw material, maximum and typical feed size, output size, capacity in t/h, project country, site photos and budget range. Add the product sieve specification, allowed oversize, representative feed grading, intended downstream receiver, proposed bypass route and the sample point to be used for acceptance.
Sources and technical references
Sources retrieved 2026-11-21. Other OEM documentation supports general technical distinctions and the attributed chart example; it does not establish MVSI model limits or performance.
- MVSI Mobile Primary Jaw Crusher, linked above: the relevant primary-jaw product family and application scope.
- Metso Nordberg C-series application guide, linked above, printed pages 4 and 6: setting conventions, manual limits and operating factors.
- Terex Cedarapids/Simplicity/Canica 2025 pocket reference, linked above, printed page 38: open-circuit jaw product percent-passing example.
- Terex EvoQuip wear-parts guide, linked above, printed pages 16–17: setting measurement, manual minimum and wear implication.