crushing strength of aggregate pdf

ENGINEERED FOR YOUR MATERIAL

Tell Us About Your Project

Share your material and required throughput. Our engineers will recommend the right crushing, sand making or beneficiation solution.

Crushing Strength of Aggregate PDF: A Complete Guide to Aggregate Crushing Value (ACV) Testing

Crushing strength of aggregate is one of the most important mechanical properties governing the performance of concrete, asphalt, and pavement base courses. If you are searching for a crushing strength of aggregate PDF resource, this guide consolidates everything you need: definitions, test procedures (BS 812-110 and IS 2386 Part IV), calculation formulas, acceptance criteria, and factors affecting results—all in one citable reference.


What Is Crushing Strength of Aggregate?

Crushing strength of aggregate refers to the resistance of aggregate particles to compressive loading and breakdown under gradually applied load. It is most commonly expressed as the Aggregate Crushing Value (ACV)—the percentage of fines produced when a standard sample is subjected to a standardized compressive load in a steel cylinder.

A lower ACV indicates stronger aggregate; a higher value indicates weaker, more crushable material. ACV is widely used as an indirect measure of aggregate toughness and is specified in highway and structural concrete standards worldwide.

Key terms:crushing strength of aggregate pdf

  • ACV (Aggregate Crushing Value): Percentage of material passing a 2.36 mm sieve after crushing under standard load.
  • Crushing strength: The load resistance of aggregate, often reported as the 10% fines value (TFV) or ACV.
  • Ten percent fines value (TFV): Load required to produce 10% fines—a more discriminating measure for strong aggregates.

Why Crushing Strength Matters in Construction

Aggregate crushing strength directly affects:

  1. Concrete strength and durability – Weak aggregates fail prematurely under load, reducing compressive and flexural strength.
  2. Pavement performance – Base and sub-base aggregates must resist crushing under traffic and compaction loads.
  3. Bituminous mixes – Aggregate breakdown during mixing and rolling alters gradation and reduces skid resistance.
  4. Ballast and railway applications – Crushing resistance governs particle degradation under dynamic rail loads.

Specifications typically limit ACV to ≤ 30% for wearing surfaces, ≤ 45% for base courses, and ≤ 50% for other applications, depending on the standard and traffic class.


Standard Test Methods (Quick Reference)

Standard Title Key Details
BS 812-110:1990 Testing aggregates — Methods for determination of aggregate crushing value (ACV) 14.0–10.0 mm test fraction; 400 kN total load at 4 kN/s; 2.36 mm sieve
IS 2386 (Part IV):1963 Methods of test for aggregates — Mechanical properties 12.5–10 mm fraction; 400 kN in 10 minutes; ACV formula
ASTM D5821 / D6928 Aggregate toughness/abrasion (related) Micro-Deval and LA abrasion alternatives
AASHTO T 96 Los Angeles abrasion Complementary toughness indicator

Note: For very strong aggregates (ACV < 10%), the standard ACV test lacks sensitivity; the 10% fines value (TFV) test per BS 812-111 is preferred.


Aggregate Crushing Value Test Procedure (BS 812-110 / IS 2386-IV)

Apparatus Required

  • Steel cylinder (internal diameter 152 mm, depth 125 mm) with base plate and plunger
  • Compression testing machine (capable of 400 kN)
  • Sieves: 14.0 mm, 10.0 mm, 2.36 mm
  • Balance (accurate to 1 g), oven, cylindrical measure, tamping rod

Step-by-Step Procedure

  1. Prepare the sample: Oven-dry the aggregate at 105–110 °C. Sieve and retain the 14.0–10.0 mm fraction.
  2. Fill the cylinder: Fill in three layers, each tamped with 25 strokes of the tamping rod, then level the surface.
  3. Weigh the sample: Record the mass of aggregate in the cylinder (Mass A).
  4. Apply the load: Place the plunger and load at a uniform rate to reach 400 kN in 10 minutes (approximately 4 kN/s).
  5. Recover the crushed material: Remove the sample and sieve on the 2.36 mm sieve.
  6. Weigh the fines: Record the mass passing the 2.36 mm sieve (Mass B).

Calculation Formula

[
\text{ACV (\%)} = \frac{B}{A} \times 100
]

Where:

  • A = mass of test sample (g)
  • B = mass of fines passing the 2.36 mm sieve (g)

Example: If A = 3000 g and B = 660 g, then ACV = (660/3000) × 100 = 22% — acceptable for wearing-course aggregate.


Acceptance Criteria and Interpretation

ACV (%) Classification Typical Use
< 10 Exceptionally strong High-strength concrete, premium wearing courses
10–20 Strong Structural concrete, wearing surfaces
20–30 Satisfactory General concrete, base courses
30–45 Weak Base/subbase, low-traffic applications
> 45 Very weak Not recommended for structural use

Common specification limits:

  • BS 882 / EN 12620: ACV ≤ 30% for concrete aggregates (varies by application)
  • IS 383: ACV ≤ 30% for wearing surfaces, ≤ 45% for non-wearing surfaces
  • MoRTH (India): ACV ≤ 30% for bituminous wearing courses

Factors Affecting Aggregate Crushing Strength

  1. Mineralogy and petrology – Quartzite, granite, and basalt typically show low ACV; limestone and sandstone vary widely.
  2. Porosity and water absorption – Porous aggregates crush more easily; saturated samples may give higher ACV.
  3. Grain size and texture – Fine-grained, well-cemented rocks perform better.
  4. Weathering and alteration – Weathered aggregates show elevated ACV.
  5. Sample preparation – Layer thickness, tamping consistency, and moisture content affect reproducibility.
  6. Loading rate – Non-uniform loading rates bias results; the standard 4 kN/s rate must be maintained.

Test Property Measured Relationship to ACV
Los Angeles Abrasion (AASHTO T 96) Resistance to abrasion/impact Complementary; both indicate toughness
10% Fines Value (BS 812-111) Load for 10% fines More sensitive for strong aggregates
Impact Value (BS 812-112) Resistance to sudden impact Correlates with ACV but distinct loading mode
Micro-Deval (AASHTO T 327) Wet abrasion resistance Useful for polished stone evaluation

Frequently Asked Questions (FAQ)

Q1: What is a good crushing strength value for aggregate?
An ACV below 20% is considered strong; below 30% is generally acceptable for concrete and wearing courses. Values above 45% indicate weak aggregate unsuitable for structural work.crushing strength of aggregate pdf

Q2: What is the difference between ACV and 10% fines value?
ACV measures fines produced under a fixed 400 kN load. The 10% fines value measures the load required to produce exactly 10% fines—making it more discriminating for high-strength aggregates with ACV below 10%.

Q3: Can I download a crushing strength of aggregate PDF?
Yes—the primary references are BS 812-110:1990, IS 2386 (Part IV):1963, and ASTM D5821. These are available through national standards bodies (BSI, BIS, ASTM) and university libraries. Always cite the official standard edition in reports.

Q4: How many samples are needed for the ACV test?
Testing typically requires three specimens; results are averaged, and duplicate determinations should agree within specified tolerances (commonly ±2% ACV).

Q5: Does aggregate crushing strength affect concrete mix design?
Absolutely. Weak aggregates limit the achievable compressive strength and durability of concrete; mix designers should verify ACV alongside grading, absorption, and soundness.


Conclusion

The crushing strength of aggregate—quantified through the Aggregate Crushing Value test—is a fundamental quality control parameter for concrete, pavement, and railway ballast applications. By following BS 812-110 or IS 2386 (Part IV) procedures precisely and applying the ACV formula, engineers can classify aggregates and enforce specification limits with confidence.

For a printable reference, save this guide or obtain the official crushing strength of aggregate PDF from BSI, BIS, or ASTM to ensure your testing program complies with current standards.


Keywords: crushing strength of aggregate, aggregate crushing value, ACV test, crushing strength of aggregate PDF, BS 812-110, IS 2386 Part IV, aggregate testing, 10% fines value, concrete aggregate properties, pavement aggregate quality.


Posted

in

by